Williams AV IR M1 Plus Modulator
The new Williams AV IR M1 Plus Modulator is the industry’s first IR system that combines secure infrared and optional WaveCast audio over WiFi delivery in a single affordable box.
Williams AV IR M1 Plus Modulator
The new IR Plus is the industry’s first IR system that combines secure infrared and optional WaveCast audio over WiFi delivery in a single affordable box. This scalable Infrared System uses Distributed Emitter Array design to accommodate up to 16 emitters with flexible coverage in up to 288,000 square feet (26,750 square meters).
The IR Plus features a distributed infrared emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.
The rack mounted or remotely located IR modulator comes standard with support for up to four IR emitters. Each emitter runs back to the modulator via a Cat-6 cable, providing the audio and power needed to support the remote emitter. Very large room applications can be supported by adding up to four IR modulators to support a total of 16 IR emitters.
The IR Plus system can be controlled and monitored remotely via an internal webpage, allowing for easy and flexible setup and control. The integrated Ethernet provides easy connection to the building network or a dedicated system-only network.
The IR Plus system also feature a WaveCAST network output for streaming audio via WiFi when combined with a wireless access point. The WaveCAST WiFi Assistive Listening Output features an iOS or Android app for supporting mobile devices. The WaveCAST WiFi system can also be used with the Williams Sound WF R1 WiFi receiver for those that don’t want to use mobile devices.
Connect the IR M1 to a WiFi multicast router or in-house network you can stream audio over Wi-Fi to the Williams AV WaveCAST app (available in the iOS app store or Google Play store).
- Dual Technology. Industry first that combines secure infrared audio delivery and optional Wi-Fi audio delivery in a single affordable box
- Flexibility/coverage. This scalable Infrared System uses Distributed Emitter Array design to accommodate up to 16 emitters with flexible coverage in up to 288,000 square feet (26,750 square meters).
- Streamlined and cost effective install. Each emitter is connected with a single CAT 5e/6 cable that carries power and audio.
- Replaces Williams Sound MOD 232 / WIR TX9 DC and similar traditional IR products in the market.
Applications Include:
- Courtrooms
- Education
- Theaters
- Auditoriums
- Place of Worship
Features:
- Two channels of multicast Wi-Fi audio delivery to support BYOD applications. (industry first)
- Dante input option. (industry first)
- Network Control Web interface (industry first)
- IR E4 Emitter Coverage up to 18,000 Square Feet.
- Free WaveCast listening App. (Apple & Android)
- True DSP backbone allows for optimization of assistive listening for the venue
- New OLED display offers detailed status information.
- Enhanced LED technology runs cooler providing longer life span and requires less energy.
- IR M1 has firmware that can be updated in the field ensuring all emitters and arrays are compatible and up to date.
- Compatible with all Williams Sound 2.3-3.8MHz Infrared Receivers and
WF R1 Wi-Fi receivers.
| Dimensions: | 19” (W) x 1.75” (H) x 8.2” (D) (48.3 cm x 4.5 cm x 20.8 cm) |
| Weight: | 5.2lb. (2.4 kg) |
| Color: | Black |
| Rack Mount: | Single Rack Unit |
| Power Supply: | International Desktop Supply Input: 36 W, 110-240 VAC 50-60 Hz Output: +48VDC, 0.75A center-positive |
| Power Switch: | Rocker switch with LED |
| Modulation: | FM Wideband, +50kHz deviation, 50uS pre-emphasis |
| Carrier Frequency: | Selectable, 2.3/2.8 or 3.3/3.8MHz |
| Frequency Response: | 40 to 16,000Hz, +1 dB, -3dB, electrical response |
| Total Harmonic Distortion: | Less than 2%, electrical response |
| Audio Processor Functions: | DSP based; Compression 1:1, 1:5:1, or 2:1; High-pass and low-pass filter frequency control |
| Auto Carrier Shut-Off: | Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage. |
| Infrared Test LED: | Dual IR LED for receiver testing, monitoring, and audio signal testing. |
| Audio Input: | (2x) Combination 3-pin XLR, 1/4” (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power |
| Dante: | Optional |
| Internal Test Tone: | 400 Hz internal test tone selectable as audio input source for setup and diagnostics |
| Remote Configuration: | Available through embedded website |
| Headphone Output: | (2) 1/4″ headphone jacks on front panel for monitoring CH A and CH B audio inputs |
| Emitter Output Jack: | Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission. |
| Operating requirements: | 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere |
| Approvals: | CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI |
| Warranty: | 2 years on Modulator, 90 days on accessories |
The ILD122 is CE marked to all relevant safety and EMC standards.
All Ampetronic amplifiers can be used to create a system that meets the requirements of IEC118-4 and the relevant recommendation of BS7594, however the design and installation of the system is equally important to meet these Induction Loop standards.
Example Configurations:
Example 1: Single Channel
Example 2: 2 Channels
Example 3: Room Divisions
Example 4: 4 Channels
| Dimensions: | 19” (W) x 1.75” (H) x 8.2” (D) (48.3 cm x 4.5 cm x 20.8 cm) |
| Weight: | 5.2lb. (2.4 kg) |
| Color: | Black |
| Rack Mount: | Single Rack Unit |
| Power Supply: | International Desktop Supply Input: 36 W, 110-240 VAC 50-60 Hz Output: +48VDC, 0.75A center-positive |
| Power Switch: | Rocker switch with LED |
| Modulation: | FM Wideband, +50kHz deviation, 50uS pre-emphasis |
| Carrier Frequency: | Selectable, 2.3/2.8 or 3.3/3.8MHz |
| Frequency Response: | 40 to 16,000Hz, +1 dB, -3dB, electrical response |
| Total Harmonic Distortion: | Less than 2%, electrical response |
| Audio Processor Functions: | DSP based; Compression 1:1, 1:5:1, or 2:1; High-pass and low-pass filter frequency control |
| Auto Carrier Shut-Off: | Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage. |
| Infrared Test LED: | Dual IR LED for receiver testing, monitoring, and audio signal testing. |
| Audio Input: | (2x) Combination 3-pin XLR, 1/4” (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power |
| Dante: | Optional |
| Internal Test Tone: | 400 Hz internal test tone selectable as audio input source for setup and diagnostics |
| Remote Configuration: | Available through embedded website |
| Headphone Output: | (2) 1/4″ headphone jacks on front panel for monitoring CH A and CH B audio inputs |
| Emitter Output Jack: | Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission. |
| Operating requirements: | 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere |
| Approvals: | CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI |
| Warranty: | 2 years on Modulator, 90 days on accessories |
The ILD122 is CE marked to all relevant safety and EMC standards.
All Ampetronic amplifiers can be used to create a system that meets the requirements of IEC118-4 and the relevant recommendation of BS7594, however the design and installation of the system is equally important to meet these Induction Loop standards.
Example Configurations:
Example 1: Single Channel
Example 2: 2 Channels
Example 3: Room Divisions
Example 4: 4 Channels
